ASUS WL 500gP v2 / LEDE / Kernel 4.9.52

.. is working fine:
[    0.000000] Linux version 4.9.52 (lede@debian-compiler) (gcc version 5.4.0 (LEDE GCC 5.4.0 r4683+286-370aacf532) ) #0 Mon Oct 2 16:26:53 2017
[    0.000000] CPU0 revision is: 00029029 (Broadcom BMIPS3300)
[    0.000000] bcm47xx: Using ssb bus
[    0.000000] ssb: Found chip with id 0x5354, rev 0x03 and package 0x00
[    0.000000] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x14, vendor 0x4243)
[    0.000000] ssb: Core 1 found: Fast Ethernet (cc 0x806, rev 0x09, vendor 0x4243)
[    0.000000] ssb: Core 2 found: MIPS 3302 (cc 0x816, rev 0x08, vendor 0x4243)
[    0.000000] ssb: Core 3 found: USB 2.0 Host (cc 0x819, rev 0x02, vendor 0x4243)
[    0.000000] ssb: Core 4 found: MEMC SDRAM (cc 0x80F, rev 0x04, vendor 0x4243)
[    0.000000] ssb: Core 5 found: IEEE 802.11 (cc 0x812, rev 0x0D, vendor 0x4243)
[    0.000000] ssb: Core 6 found: Roboswitch (cc 0x81C, rev 0x02, vendor 0x4243)
[    0.000000] ssb: chipcommon status is 0x0
[    0.000000] ssb: Found rev 0 PMU (capabilities 0x04A63400)
[    0.000000] ssb: Initializing MIPS core...
[    0.000000] ssb: set_irq: core 0x0806, irq 4 => 4
[    0.000000] ssb: set_irq: core 0x0816, irq 5 => 2
[    0.000000] ssb: set_irq: core 0x0812, irq 2 => 5
[    0.000000] ssb: after irq reconfiguration
[    0.000000] ssb: core 0x0800, irq : 2(S)  3* 4  5  6  D  I 
[    0.000000] ssb: core 0x0806, irq : 2(S)  3  4* 5  6  D  I 
[    0.000000] ssb: core 0x0816, irq : 2(S)* 3  4  5  6  D  I 
[    0.000000] ssb: core 0x0819, irq : 2(S)  3  4  5  6* D  I 
[    0.000000] ssb: core 0x080f, irq : 2(S)  3  4  5  6  D  I*
[    0.000000] ssb: core 0x0812, irq : 2(S)  3  4  5* 6  D  I 
[    0.000000] ssb: core 0x081c, irq : 2(S)  3  4  5  6  D  I*
[    0.000000] ssb: Sonics Silicon Backplane found at address 0x18000000
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes.
[    0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] On node 0 totalpages: 16384
[    0.000000] free_area_init_node: node 0, pgdat 80383014, node_mem_map 81000020
[    0.000000]   Normal zone: 128 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 16384 pages, LIFO batch:3
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: noinitrd console=ttyS0,115200
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Memory: 60852K/65536K available (3090K kernel code, 135K rwdata, 372K rodata, 168K init, 282K bss, 4684K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:128
[    0.000000] MIPS: machine is Asus WL500GP V2
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 15927170388 ns
[    0.000029] sched_clock: 32 bits at 120MHz, resolution 8ns, wraps every 17895697403ns
[    0.000141] Calibrating delay loop... 239.61 BogoMIPS (lpj=1198080)
[    0.070064] pid_max: default: 32768 minimum: 301
[    0.070512] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.070573] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.080454] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.080544] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.082821] NET: Registered protocol family 16
[    0.084652] Can't analyze schedule() prologue at 80301a4c
[    0.141440] clocksource: Switched to clocksource MIPS
[    0.150061] NET: Registered protocol family 2
[    0.153223] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.153414] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    0.153567] TCP: Hash tables configured (established 1024 bind 1024)
[    0.154321] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.154479] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.155409] NET: Registered protocol family 1
[    0.155601] PCI: CLS 0 bytes, default 16
[    0.176754] Crashlog allocated RAM at address 0x3f00000
[    0.183352] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[    0.210134] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.210197] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.251917] io scheduler noop registered
[    0.251979] io scheduler deadline registered (default)
[    0.252555] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
[    0.254884] console [ttyS0] disabled
[    0.275267] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 3, base_baud = 1562500) is a U6_16550A
[    0.612703] console [ttyS0] enabled
[    0.637742] serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 3, base_baud = 1562500) is a U6_16550A
[    0.649334] physmap platform flash device: 02000001 at 1c000000
[    0.655855] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
[    0.666676] physmap-flash.0: Found an alias at 0x800000 for the chip at 0x0
[    0.666711] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0
[    0.666739] physmap-flash.0: Found an alias at 0x1800000 for the chip at 0x0
[    0.666783] Amd/Fujitsu Extended Query Table at 0x0040
[    0.672281]   Amd/Fujitsu Extended Query version 1.1.
[    0.677552] number of CFI chips: 1
[    0.696749] 3 bcm47xxpart partitions found on MTD device physmap-flash.0
[    0.703868] Creating 3 MTD partitions on "physmap-flash.0":
[    0.709705] 0x000000000000-0x000000020000 : "boot"
[    0.724906] 0x000000020000-0x0000007f0000 : "firmware"
[    0.736988] 3 trx partitions found on MTD device firmware
[    0.742783] Creating 3 MTD partitions on "firmware":
[    0.747987] 0x00000000001c-0x000000000920 : "loader"
[    0.759640] 0x000000000920-0x00000012a800 : "linux"
[    0.771132] 0x00000012a800-0x0000007d0000 : "rootfs"
[    0.782975] mtd: device 4 (rootfs) set to be root filesystem
[    0.788926] 1 squashfs-split partitions found on MTD device rootfs
[    0.795548] 0x000000340000-0x0000007d0000 : "rootfs_data"
[    0.807643] 0x0000007f0000-0x000000800000 : "nvram"
[    0.829781] libphy: Fixed MDIO Bus: probed
[    0.834676] b44: Broadcom 44xx/47xx 10/100 PCI ethernet driver version 2.0
[    0.851344] libphy: b44_eth_mii: probed
[    0.983936] b53_common: found switch: BCM5325, rev 0
[    0.989192] Broadcom B53 (1) 1:1e: attached PHY driver [Broadcom B53 (1)] (mii_bus:phy_addr=1:1e, irq=-1)
[    0.999264] b44 ssb0:0 eth0: Broadcom 44xx/47xx 10/100 PCI ethernet driver bc:ae:c5:__:__:__
[    1.009526] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds, Software Timer)
[    1.019277] GPIO_WDT: failed to register misc device
[    1.027683] NET: Registered protocol family 10
[    1.042538] NET: Registered protocol family 17
[    1.047381] 8021q: 802.1Q VLAN Support v1.8
[    1.064986] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    1.075539] Freeing unused kernel memory: 168K
[    1.080178] This architecture does not have kernel memory protection.
[    2.097197] init: Console is alive
[    2.101691] init: - watchdog -
[    2.501524] random: fast init done
[    3.525778] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    3.631839] usbcore: registered new interface driver usbfs
[    3.637948] usbcore: registered new interface driver hub
[    3.644085] usbcore: registered new device driver usb
[    3.667592] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    3.679087] ehci-platform: EHCI generic platform driver
[    3.684958] ehci-platform ehci-platform.0: EHCI Host Controller
[    3.691371] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
[    3.700532] ehci-platform ehci-platform.0: irq 6, io mem 0x18003800
[    3.731593] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
[    3.742088] hub 1-0:1.0: USB hub found
[    3.747296] hub 1-0:1.0: 2 ports detected
[    3.761202] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    3.771658] ohci-platform: OHCI generic platform driver
[    3.777383] ohci-platform ohci-platform.0: Generic Platform OHCI controller
[    3.784934] ohci-platform ohci-platform.0: new USB bus registered, assigned bus number 2
[    3.793751] ohci-platform ohci-platform.0: irq 6, io mem 0x18003000
[    3.869387] hub 2-0:1.0: USB hub found
[    3.874910] hub 2-0:1.0: 2 ports detected
[    3.889364] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    3.908177] init: - preinit -
[    4.224297] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    4.551361] hub 1-1:1.0: USB hub found
[    4.606889] hub 1-1:1.0: 2 ports detected
[    6.901702] b44 ssb0:0 eth0: Link is up at 100 Mbps, half duplex
[    6.907982] b44 ssb0:0 eth0: Flow control is off for TX and off for RX
[    8.001575] b44 ssb0:0 eth0: Link is Up - 100Mbps/Full - flow control off
[   10.590134] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[   10.661242] urandom-seed: Seed file not found (/etc/urandom.seed)
[   10.797053] b44 ssb0:0 eth0: powering down PHY
[   10.854587] procd: - early -
[   10.857982] procd: - watchdog -
[   11.121736] b44 ssb0:0 eth0: Link is Down
[   11.636444] procd: - watchdog -
[   11.640945] procd: - ubus -
[   11.774043] procd: - init -
[   12.806923] kmodloader: loading kernel modules from /etc/modules.d/*
[   12.876470] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   12.916195] Loading modules backported from Linux version v4.14-rc2-0-ge19b205be43d
[   12.924313] Backport generated by backports.git v4.14-rc2-1-0-g8bfe0960
[   12.939426] ip_tables: (C) 2000-2006 Netfilter Core Team
[   12.970387] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
[   13.124021] xt_time: kernel timezone is -0000
[   13.618332] PPP generic driver version 2.4.2
[   13.630672] NET: Registered protocol family 24
[   13.783758] b43-phy0: Broadcom 5354 WLAN found (core revision 13)
[   13.815647] b43-phy0: Found PHY: Analog 6, Type 5 (LP), Revision 0
[   13.822224] b43-phy0: Found Radio: Manuf 0x17F, ID 0x2062, Revision 1, Version 0
[   13.856133] Broadcom 43xx driver loaded [ Features: PNL ]
[   13.944739] kmodloader: done loading kernel modules from /etc/modules.d/*
[   14.017811] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[   28.039035] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[   28.062178] jffs2_build_filesystem(): unlocking the mtd device... 
[   28.068427] done.
[   28.070446] jffs2_build_filesystem(): erasing all blocks after the end marker... 
[   36.536662] b44 ssb0:0 eth0: Link is up at 100 Mbps, full duplex
[   36.543103] b44 ssb0:0 eth0: Flow control is off for TX and off for RX
[   36.670727] br-lan: port 1(eth0.1) entered blocking state
[   36.676536] br-lan: port 1(eth0.1) entered disabled state
[   36.685837] device eth0.1 entered promiscuous mode
[   36.690842] device eth0 entered promiscuous mode
[   36.841194] br-lan: port 1(eth0.1) entered blocking state
[   36.846989] br-lan: port 1(eth0.1) entered forwarding state
[   37.601715] b44 ssb0:0 eth0: Link is Up - 100Mbps/Full - flow control off
[   69.624056] done.
[   69.626198] jffs2: notice: (791) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[  119.231684] random: crng init done
BusyBox v1.27.2 () built-in shell (ash)

     _________
    /        /\      _    ___ ___  ___
   /  LE    /  \    | |  | __|   \| __|
  /    DE  /    \   | |__| _|| |) | _|
 /________/  LE  \  |____|___|___/|___|                      lede-project.org
 \        \   DE /
  \    LE  \    /  -----------------------------------------------------------
   \  DE    \  /    Reboot (SNAPSHOT, r4683+286-370aacf532)
    \________\/    -----------------------------------------------------------

=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@LEDE:~# uname -a
Linux LEDE 4.9.52 #0 Mon Oct 2 16:26:53 2017 mips GNU/Linux

root@LEDE:~# cat /proc/cpuinfo
system type		: Broadcom BCM5354
machine			: Asus WL500GP V2
processor		: 0
cpu model		: Broadcom BMIPS3300 V2.9
BogoMIPS		: 239.61
wait instruction	: yes
microsecond timers	: yes
tlb_entries		: 32
extra interrupt vector	: yes
hardware watchpoint	: no
isa			: mips1 mips2 mips32r1
ASEs implemented	: mips16
shadow register sets	: 1
kscratch registers	: 0
package			: 0
core			: 0
VCED exceptions		: not available
VCEI exceptions		: not available